This ribbon organizer tote is easy to make, inexpensive and stackable. I contemplated other storage methods that involved affixing the ribbon spools to a stationary rack, (wall-mounted, etc.) but opted for the flexibility of being able to store and use the ribbon in a variety of locations with this system.
DIY RIBBON ORGANIZER
SUPPLIES NEEDED
A sturdy plastic container with lid
5/16” Wooden dowels
A 5/16” drill bit and drill
Permanent marker
Hot glue gun
¾ inch, wooden, screw-hole plugs (alternatively, Tinker toys may fit these
dowels. I think they would be adorable on both ends, but would be glued on the finished end only.)
LET’S MAKE IT!
Measure and mark the spacing of dowel holes on the container with a permanent marker. On each side of the box, the first holes should be approximately 2.5” from the short end of the box, approximately 2.5-3” down into the depth of the box, and a minimum of 5 inches away from each other going down the length of the box. (Use ribbon spools to gauge placement, making sure that they match up on the opposite side. Mark as many holes as will fit spools and dowels. I used three dowels.)
Using 5/16” bit, drill the holes in the container according to the marks.
For dowel length, measure container’s width and add 2 inches to measurement. (The dowels will extend about an inch or so beyond the outside of the container.)
Cut all dowels to measured length. (Dowels are small enough to use a serrated knife to score around the dowel and then snap off the excess.)
Using 5/16” bit, drill holes in the wooden screw-hole plugs half way through. Put some glue inside the hole and insert a dowel, which should fit tightly.
When glue is dry, push a dowel through one hole in the box & load it up with ribbon. When full, push the dowel through the second,
corresponding hole.
I thought I might need something to secure the unfinished end of
the dowel in place, but the dowels fit so tightly that they stay in place without help. I secure the ribbon ends to the rest of the spool with
either a small tab of tape or a sewing pin.
This was shared here: Cheerios & Lattes,I Gotta Try That, Lou Lou Girls,Made In a Day, Sewlicious Home Decor, Wake up Wednesday
Kathy Shea Mormino
Affectionately known internationally as The Chicken Chick®, Kathy Shea Mormino shares a fun-loving, informative style to raising backyard chickens. …Read on
shop my SPONSORS
This ribbon organizer tote is easy to make, inexpensive and stackable. I contemplated other storage methods that involved affixing the ribbon spools to a stationary rack, (wall-mounted, etc.) but opted for the flexibility of being able to store and use the ribbon in a variety of locations with this system.
DIY RIBBON ORGANIZER
SUPPLIES NEEDED
A sturdy plastic container with lid
5/16” Wooden dowels
A 5/16” drill bit and drill
Permanent marker
Hot glue gun
¾ inch, wooden, screw-hole plugs (alternatively, Tinker toys may fit these
dowels. I think they would be adorable on both ends, but would be glued on the finished end only.)
LET’S MAKE IT!
Measure and mark the spacing of dowel holes on the container with a permanent marker. On each side of the box, the first holes should be approximately 2.5” from the short end of the box, approximately 2.5-3” down into the depth of the box, and a minimum of 5 inches away from each other going down the length of the box. (Use ribbon spools to gauge placement, making sure that they match up on the opposite side. Mark as many holes as will fit spools and dowels. I used three dowels.)
Using 5/16” bit, drill the holes in the container according to the marks.
For dowel length, measure container’s width and add 2 inches to measurement. (The dowels will extend about an inch or so beyond the outside of the container.)
Cut all dowels to measured length. (Dowels are small enough to use a serrated knife to score around the dowel and then snap off the excess.)
Using 5/16” bit, drill holes in the wooden screw-hole plugs half way through. Put some glue inside the hole and insert a dowel, which should fit tightly.
When glue is dry, push a dowel through one hole in the box & load it up with ribbon. When full, push the dowel through the second,
corresponding hole.
I thought I might need something to secure the unfinished end of
the dowel in place, but the dowels fit so tightly that they stay in place without help. I secure the ribbon ends to the rest of the spool with
either a small tab of tape or a sewing pin.
This was shared here: Cheerios & Lattes,I Gotta Try That, Lou Lou Girls,Made In a Day, Sewlicious Home Decor, Wake up Wednesday
Antonella, I'm a new follower of your blog and would love to have you link up at my weekly Clever Chicks Blog Hop. I had never heard of quilling- your work is beautiful! This week's party can be found here: I would love to have you to link up at my weekly Clever Chicks Blog Hop: https://the-chicken-chick.com/2013/09/clever-chicks-blog-hop-50-includes-3.html I hope you can make it!
Will do, Antonella! Thanks for stopping by!
this is a wonderful to keep all the ribbons. thank you so much for posting. i will be this.
WOW! What a great way to store your ribbon, love the fact that it is stackable!
I linked over from the Work It Wednesday Link Party where I am participating too and would love it if you'd stop by.
Hugs, antonella :-)
Antonella's Quilling Blog
Thank you for joining the train ride. I always hope to have my own chickens someday.