Winter brings many challenges for the backyard chicken-keeper, and frozen water is chief among them.  You can make your own waterer heater for use with either metal or plastic waterers. It will cost less than $10, cost pennies to run and you can complete the project in under ten minutes! Make your own waterer heater for use with either metal or plastic waterers. It will cost less than $10, cost pennies to run and you can complete the project in under ten minutes!

We had record-breaking, sub-zero temperatures for long periods of time in 2010 here in Connectictut and my waterers never iced over the way they used to without these heaters.  It doesn’t seem as though a humble, 40 watt lightbulb should be able to produce enough warmth to keep the water in a plastic waterer from icing over, but remarkably, it does!

It doesn't seem as though a humble, 40 watt lightbulb should be able to produce enough warmth to keep the water in a plastic waterer from icing over, but remarkably, it does!

Supplies:

  • 10″, metal cookie tin (available at most dollar & thrift stores & likely in your garage or basement)
  • lamp assembly kit (available oniline, at hardware & home improvement stores OR buy a thrift store/tag sale lamp and take it apart)0
  • 40 watt, incandescent light bulb (in deep-freeze conditions, use a 60 watt bulb)(in light of the government phase-out, some users recommend 40 watt candelabra bulbs or CFL bulbs, but I have not, so I cannot vouch for their effectiveness)
  • Drill with 3/8″ drill bit
Lamp assembly parts.
Lamp assembly parts

INSTRUCTIONS:

1. Drill a hole in the side of the cookie tin.

String the pre-threaded lamp stem assembly through the hole & tighten the screw on the stem.

2. String the pre-threaded lamp stem assembly through the hole & tighten the screw on the stem.

Screw in the light bulb.

3. Screw in the light bulb. Voila!

TO USE:

Put the top on the cookie tin and place the tin on a cinder block or another level surface in the chicken run.  Plug into a GFI outlet. Place metal or plastic waterer on top of the water heater when freezing temperatures are anticipated. Disconnect when not in use or use a ThermoCube to turn the unit on when temperatures reache 35°F.

It doesn't seem as though a humble, 40 watt lightbulb should be able to produce enough warmth to keep the water in a plastic waterer from icing over, but remarkably, it does!

When I made my first cookie tin water heater, I found it difficult to believe that this device, which barely felt warm to the touch, could possibly do the intended job. I was only convinced the first frigid morning I went out into the run and found no ice ring to chip out of the waterer. You may have to try it to believe it too.

Plastic Poultry waterer on Cookie tin water heater

Kathy Shea Mormino

Affectionately known internationally as The Chicken Chick®, Kathy Shea Mormino shares a fun-loving, informative style to raising backyard chickens. …Read on

shop my SPONSORS

Winter brings many challenges for the backyard chicken-keeper, and frozen water is chief among them.  You can make your own waterer heater for use with either metal or plastic waterers. It will cost less than $10, cost pennies to run and you can complete the project in under ten minutes! Make your own waterer heater for use with either metal or plastic waterers. It will cost less than $10, cost pennies to run and you can complete the project in under ten minutes!

We had record-breaking, sub-zero temperatures for long periods of time in 2010 here in Connectictut and my waterers never iced over the way they used to without these heaters.  It doesn’t seem as though a humble, 40 watt lightbulb should be able to produce enough warmth to keep the water in a plastic waterer from icing over, but remarkably, it does!

It doesn't seem as though a humble, 40 watt lightbulb should be able to produce enough warmth to keep the water in a plastic waterer from icing over, but remarkably, it does!

Supplies:

  • 10″, metal cookie tin (available at most dollar & thrift stores & likely in your garage or basement)
  • lamp assembly kit (available oniline, at hardware & home improvement stores OR buy a thrift store/tag sale lamp and take it apart)0
  • 40 watt, incandescent light bulb (in deep-freeze conditions, use a 60 watt bulb)(in light of the government phase-out, some users recommend 40 watt candelabra bulbs or CFL bulbs, but I have not, so I cannot vouch for their effectiveness)
  • Drill with 3/8″ drill bit
Lamp assembly parts.
Lamp assembly parts

INSTRUCTIONS:

1. Drill a hole in the side of the cookie tin.

String the pre-threaded lamp stem assembly through the hole & tighten the screw on the stem.

2. String the pre-threaded lamp stem assembly through the hole & tighten the screw on the stem.

Screw in the light bulb.

3. Screw in the light bulb. Voila!

TO USE:

Put the top on the cookie tin and place the tin on a cinder block or another level surface in the chicken run.  Plug into a GFI outlet. Place metal or plastic waterer on top of the water heater when freezing temperatures are anticipated. Disconnect when not in use or use a ThermoCube to turn the unit on when temperatures reache 35°F.

It doesn't seem as though a humble, 40 watt lightbulb should be able to produce enough warmth to keep the water in a plastic waterer from icing over, but remarkably, it does!

When I made my first cookie tin water heater, I found it difficult to believe that this device, which barely felt warm to the touch, could possibly do the intended job. I was only convinced the first frigid morning I went out into the run and found no ice ring to chip out of the waterer. You may have to try it to believe it too.

Plastic Poultry waterer on Cookie tin water heater
Subscribe
Notify of
guest
580 Comments
Inline Feedbacks
View all comments
Cindy
Cindy
1 year ago

Love the nipple drinker

Paige W
Paige W
2 years ago

Does it matter if the bulb is LED? That is what I have on hand currently.

Cricket Brooks
Cricket Brooks
2 years ago

This works great! I added a pinhole in the side of the cookie tin facing the house so at night I can see that the light inside is on. It should be easy to see if the bulb burns out.

1 107 108 109